The Kedis CNC Surf machine is the Disk machine from Brasil. The Surfmach is an affordable machine designed by Miguel Jorge in Brasil. The Uno shaper is a Spanish machine that works perfectly with Shape3d. The Precision shaper machine is an American machine that can be used with Shape3d (Seattle). Scanning of existing boards is also available from CNT Motion Systems. You can’t go wrong with Shape3D and a CNC machine from CNT Motion Systems. CNT Motion Systems Surfboard Shaping Machines are all around the world.The 3emmegi machine is fully equiped, and comes with Shape3d (Massimo Morini, Italy). Contact us if you want to replace Aku shaper by Shape3d X to improve the capabilities of your machine! The Aku machine works perfectly with Shape3d X. The real APS3000 machine now comes with Shape3d, and get even better (Miki Langenbach, Australia). In addition to its high performance surfboard shaping, it will take on hotwire cutting, 3D Scanning, G-Code file cutting, etc. The KMSYSTEM CNC Machines is now compatible with Shape3D, The French machine just keeps getting better. The 3DM machine works so well with Shape3d, it is now a best seller (John Yow, Hawaii). If you want to build a machine that work with Shape3d, we'll make it work. If you want to buy a CNC machine that works with Shape3d, you have the choice. s3d files a common format for board design. More than ten types of CNC machines are now driven by Shape3d all over the world, making the. The "v" through the middle helps with control, particularly when transitioning from rail to rail.Shape3d is compatible with almost all the CNC machines in the world, and can be adapted to any new one. The Double Concave Hull features 2 concaves on either side of the hull. This splits the water flow into double channels, creating lift underneath the back foot and ultimately loosening up the board This concave is primarily used on our Slasher DK model. ![]() This creates extra lift and drive from your shoulder / elbows, while still allowing plenty of hold through your hips.īy having a long, but subtle channel such as this, it also means we need less channels on the slick to keep the board holding in.įun fact: if you were to continue drawing the lines of the channel off into the spaces of the board, they would eventually loop back into themselves to make the torodial shape. This allows water to be welcomed into the channel then squeezed through the narrower centre point at a greater speed, before released through the slight concave in the tail at a reduced pressure, much like the Venturi effect. On the torus channel, the wider points of the centre channel are at the nose and the tail of the board. Once again, we have continued with a variation of the planing hull, whilst being mindful of the drive and hold required on a bodyboard. The Torus channel is an evolution of our Zero Slot Hull Channel, and is our newest bottom contour innovation. We also use it with regular rails on the Slider model, making it the ideal small wave board. It features a large single hull concave that runs through the middle of the board.Ī lot of our inspiration came from the Bob Simmons designed Mini Simmons surfboards, which have since evolved and are evident in a lot of the modern day Daniel Thompson (Tomo Shapes) and Slater Designs surfboards.Īs you lose the hold provided with regular channels, we most commonly use this combined with the Vax Trax Rails for a bit of extra hold. ![]() This bottom contour is based on the theory of a "planing hull" which as the name suggests, gets you planing earlier and easier, giving exceptional down the line speed off the weakest of sections. We use this channel system on our Bullet boards, and have used it on our Speed Dealer models in the past. To sum it up simply, they provide better speed, drive and control, particularly in average to good waves, that aren't heaps slabby. ![]() ![]() Being longer in length with extremely slight graduation, means these channels keep harmony and flow, allowing water to enter and exit cleanly with minimal disturbance. The Transitional Hull Channels start about 18 inches from the tail of the board (almost double the length of traditional channels). This is a channel we developed with the help of Steve "Bullet" Mackenzie. They are found on our Pro Model Boards such as the Golden Child, Lip Reader & Wingass Models They are lightly graduated to give the rider the perfect balance of hold on the face, release when you need it, and speed! These are the most common channels we use, and closest to the traditional bodyboard style channel.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |